Posts

Overboard Discharge Services In Maine Today

Septic Preservation Services has Overboard Discharge Services and Repairs scheduled today in Tenants Harbor, Friendship, Bremen, Owl’s Head, Islesboro and Union ME. For more information regarding OBDs see Maine Gov

These are a few general tips that will help to extend the life of your OBD and promote high quality effluent.

  • Some household chemicals kill the microorganisms that digest the wastes in your treatment system and may pass through to the receiving waterbody. Toxic chemicals, harsh cleaners, paint, pharmaceuticals, and non-biodegradable materials should not be disposed of by dumping or pouring down the drain.
  • Using low-flow toilets and water-saving showerheads will prolong the life of your system.
  • Septic tanks should be pumped at least once every three years. Depending on how much the OBD facility is used, you may want to increase the septic pumping frequency or decrease it to once every five years if it receives very little use.
  • Trees, shrubs and woody perennials should be cleared away from system components. Sandfilter surfaces should be mowed at least once per year. If a wet spot appears on or near the sandfilter bed notify the DEP inspector.
  • Mechanical systems operate best if they are used at a consistent rate and may malfunction or produce poor quality effluent if overloaded on the weekend and “starved” during the week. Try to manage laundry, cleaning, and showers so that the load is spread out as evenly as possible. Leave a mechanical OBD operating as recommended by your service contractor at all times during the season of use.
  • Check the chlorine level at least every two weeks and keep fresh chlorine in contact with the treated wastewater. Don’t overfill the chlorinator tubes; only the bottom two or three inches of the tubes should have chlorine. Old, brown or mushy chlorine does not properly disinfect and must be replaced. Take care to remove old chlorine from your chlorinator rather than washing it out to the waterbody.
  • Ensure that the outfall pipe extends to below the low water mark of the receiving waterbody. In extenuating circumstances a specific waiver to this requirement may be granted by the Department.
  • Treated wastewater should be clear and without a strong septic or chlorine odor. If wastewater in the disinfection unit is not nearly clear, smells like rotten eggs, raw sewage, or smells strongly of chlorine, call your service contractor or notify the DEP inspector.

If you require an Overboard Discharge Service or Repair you will need to contact a certified maintenance contractor. Septic Preservation Services is the only Statewide contractor on the Maine Department of Environmental Protection Wastewater Treatment Plants certified maintenance contractors list. If you wish to make an appointment or if you have any questions about our Overboard Discharge Services please do contact our office on 877-378-4279 or visit Septic Preservation Services

OBD Services and Repairs in Maine

Septic Preservation Services have OBD services and repairs scheduled in Arrowsic, Boothbay, Westport Island, Bremen, Friendship, West Bath and Richmond Maine. The Maine DEP’s Overboard Discharge (OBD) Program is responsible for regulating discharges of sanitary and household wastewater generated at residential or commercial locations to streams, rivers, bays, and the ocean. All OBDs must be approved by the DEP through a licensing process. DEP rule requires all mechanical OBD treatment systems to have an operating alarm system; to maintain a current service contract with a licensed service contractor; and to attach a service tag on or near the treatment system that provides the service contractor’s name and the last date of service. All mechanical systems require power, so be sure that power is supplied to the unit and that it is turned on 7 days a week during the season of use. Septic Preservation Services are the only statewide contractor on the OBD service contractor list supplied by the Maine Department of Environmental Protection. If you need to arrange OBD services or repairs please do contact our office on 877-378-4279 or visit Septic Preservation Services

Septic Preservation Services Provides OBD Services and Repairs to Maine Customers

Septic Preservation Services have Overboard Discharge (OBD) Services and Repairs today in Kittery, Kittery Point, Cape Neddick, Wells and North Berwick Maine. As stated on the Maine Gov Department of Environmental Protection website:

“The Maine DEP’s Overboard Discharge (OBD) Program is responsible for regulating discharges of sanitary and household wastewater generated at residential or commercial locations to streams, rivers, bays, and the ocean. All OBDs must be approved by the DEP through a licensing process.”

Septic Preservation Services are the only statewide contractor listed by the Maine Department of Environmental Protection on their Wastewater Treatment Plant Certified Maintenance Contractor List.

It is stated that for OBDs the

“DEP rule requires all mechanical treatment systems to have an operating alarm system; to maintain a current service contract with a licensed service contractor; and to attach a service tag on or near the treatment system that provides the service contractor’s name and the last date of service.”

Therefore all property owners with an OBD must have a service contract with a licensed OBD. Septic Preservation Services has extensive experience and provides OBD services for multiple customers in Maine. If you require an Overboard Discharge Service or Overboard Discharge Repair please do contact our office on 877-378-4279 or visit Septic Preservation Services

Maine

Overboard Discharge Services

Check out this great video.  We are ready for all your questions and concerns with Maine Overboard Discharge Services (OBD).  Visit www.septicpreservation.com for more information.

Extend The Life Of Your Maine OBD

Septic Preservation Services has Overboard Discharge Services and Repairs scheduled today in Kittery Point, Cape Neddick, Wells, Kennebunk Port, Biddeford and Old Orchard Beach ME. For more information regarding OBDs see:

https://www1.maine.gov/dep/water/wd/OBD/ip_obd.pdf

These are a few general tips that will help to extend the life of your OBD and promote high quality effluent.

  • Some household chemicals kill the microorganisms that digest the wastes in your treatment system and may pass through to the receiving waterbody. Toxic chemicals, harsh cleaners, paint, pharmaceuticals, and non-biodegradable materials should not be disposed of by dumping or pouring down the drain.
  • Using low-flow toilets and water-saving showerheads will prolong the life of your system.
  • Septic tanks should be pumped at least once every three years. Depending on how much the OBD facility is used, you may want to increase the septic pumping frequency or decrease it to once every five years if it receives very little use.
  • Trees, shrubs and woody perennials should be cleared away from system components. Sandfilter surfaces should be mowed at least once per year. If a wet spot appears on or near the sandfilter bed notify the DEP inspector.
  • Mechanical systems operate best if they are used at a consistent rate and may malfunction or produce poor quality effluent if overloaded on the weekend and “starved” during the week. Try to manage laundry, cleaning, and showers so that the load is spread out as evenly as possible. Leave a mechanical OBD operating as recommended by your service contractor at all times during the season of use.
  • Check the chlorine level at least every two weeks and keep fresh chlorine in contact with the treated wastewater. Don’t overfill the chlorinator tubes; only the bottom two or three inches of the tubes should have chlorine. Old, brown or mushy chlorine does not properly disinfect and must be replaced. Take care to remove old chlorine from your chlorinator rather than washing it out to the waterbody.
  • Ensure that the outfall pipe extends to below the low water mark of the receiving waterbody. In extenuating circumstances a specific waiver to this requirement may be granted by the Department.
  • Treated wastewater should be clear and without a strong septic or chlorine odor. If wastewater in the disinfection unit is not nearly clear, smells like rotten eggs, raw sewage, or smells strongly of chlorine, call your service contractor or notify the DEP inspector.

If you require an Overboard Discharge Service or repair you will need to contact a certified maintenance contractor. Septic Preservation Services is the only Statewide contractor on the Maine Department of Environmental Protection Wastewater Treatment Plants certified maintenance contractors list. If you wish to make an appointment or if you have any questions please do contact our office on 877-378-4279 or visit https://www.septicpreservation.com

The Only Statewide Contractor On The Overboard Discharge (OBD) Service Contractor List

Septic Preservation Services have overboard discharge (OBD) services and repairs scheduled today in Biddeford, Kennebunk Port, Kennebunk, Falmouth, Cape Elizabeth, Old Orchard Beach and Arundel Maine. The Maine DEP’s Overboard Discharge (OBD) Program is responsible for regulating discharges of sanitary and household wastewater generated at residential or commercial locations to streams, rivers, bays, and the ocean. All OBDs must be approved by the DEP through a licensing process. DEP rule requires all mechanical OBD treatment systems to have an operating alarm system; to maintain a current service contract with a licensed service contractor; and to attach a service tag on or near the treatment system that provides the service contractor’s name and the last date of service. Septic Preservation Services are the only statewide contractor on the OBD service contractor list supplied by the Maine Department of Environmental Protection. If you need to arrange an overboard discharge (OBD) service or repair please do contact our office on 877-378-4279 or visit https://www.septicpreservation.com

Tips To Help Extend The Life Of Your OBD

Septic Preservation Services has Overboard Discharge Services (OBD) and Repairs scheduled today in Tenants Harbor, Friendship, Bremen, Owl’s Head, Islesboro and Union ME. For more information regarding OBDs see:

https://www1.maine.gov/dep/water/wd/OBD/ip_obd.pdf

These are a few general tips that will help to extend the life of your OBD and promote high quality effluent.

  • Some household chemicals kill the microorganisms that digest the wastes in your treatment system and may pass through to the receiving waterbody. Toxic chemicals, harsh cleaners, paint, pharmaceuticals, and non-biodegradable materials should not be disposed of by dumping or pouring down the drain.
  • Using low-flow toilets and water-saving showerheads will prolong the life of your system.
  • Septic tanks should be pumped at least once every three years. Depending on how much the OBD facility is used, you may want to increase the septic pumping frequency or decrease it to once every five years if it receives very little use.
  • Trees, shrubs and woody perennials should be cleared away from system components. Sand filter surfaces should be mowed at least once per year. If a wet spot appears on or near the sand filter bed notify the DEP inspector.
  • Mechanical systems operate best if they are used at a consistent rate and may malfunction or produce poor quality effluent if overloaded on the weekend and “starved” during the week. Try to manage laundry, cleaning, and showers so that the load is spread out as evenly as possible. Leave a mechanical OBD operating as recommended by your service contractor at all times during the season of use.
  • Check the chlorine level at least every two weeks and keep fresh chlorine in contact with the treated wastewater. Don’t overfill the chlorinator tubes; only the bottom two or three inches of the tubes should have chlorine. Old, brown or mushy chlorine does not properly disinfect and must be replaced. Take care to remove old chlorine from your chlorinator rather than washing it out to the waterbody.
  • Ensure that the outfall pipe extends to below the low water mark of the receiving waterbody. In extenuating circumstances a specific waiver to this requirement may be granted by the Department.
  • Treated wastewater should be clear and without a strong septic or chlorine odor. If wastewater in the disinfection unit is not nearly clear, smells like rotten eggs, raw sewage, or smells strongly of chlorine, call your service contractor or notify the DEP inspector.

If you require an Overboard Discharge Service or repair you will need to contact a certified maintenance contractor. Septic Preservation Services is the only Statewide contractor on the Maine Department of Environmental Protection Wastewater Treatment Plants certified maintenance contractors list. If you wish to make an appointment or if you have any questions please do contact our office on 877-378-4279 or visit https://www.septicpreservation.com

Maine OBD Services and OBD Repairs

Septic Preservation Services have overboard discharge (OBD) services and repairs scheduled today in Arrowsic, Boothbay, Westport Island, Bremen, Friendship, West Bath and Richmond Maine. The Maine DEP’s Overboard Discharge (OBD) Program is responsible for regulating discharges of sanitary and household wastewater generated at residential or commercial locations to streams, rivers, bays, and the ocean. All OBDs must be approved by the DEP through a licensing process. DEP rule requires all mechanical OBD treatment systems to have an operating alarm system; to maintain a current service contract with a licensed service contractor; and to attach a service tag on or near the treatment system that provides the service contractor’s name and the last date of service. All mechanical systems require power, so be sure that power is supplied to the unit and that it is turned on 7 days a week during the season of use. Septic Preservation Services are the only statewide contractor on the OBD service contractor list supplied by the Maine Department of Environmental Protection. If you need to arrange an overboard discharge (OBD) service or repair please do contact our office on 877-378-4279 or visit https://www.septicpreservation.com

The Maine DEP’s Overboard Discharge (OBD) Program Is Responsible For Regulating Discharges Of Sanitary And Household Wastewater

Septic Preservation Services have many years experience working with the Maine government’s overboard discharge (OBD) program. As stated on the Maine Gov website:

“The Maine DEP’s Overboard Discharge (OBD) Program is responsible for regulating discharges of sanitary and household wastewater generated at residential or commercial locations to streams, rivers, bays, and the ocean. All OBDs must be approved by the DEP through a licensing process.” For more information see:

http://www.maine.gov/dep/water/wd/OBD/index.html

Septic Preservation Services are the only statewide company on the certified maintenance contractor list provided by the Maine Department of Environmental Protection.

In addition to having your OBD serviced and maintained by a certified contractor you can ensure that your OBD is maintained by following these tips that will help to extend the life of your OBD and promote high quality effluent.

  • Some household chemicals kill the microorganisms that digest the wastes in your treatment system and may pass through to the receiving waterbody. Toxic chemicals, harsh cleaners, paint, pharmaceuticals, and non-biodegradable materials should not be disposed of by dumping or pouring down the drain.
  • Using low-flow toilets and water-saving showerheads will prolong the life of your system.
  • Septic tanks should be pumped at least once every three years. Depending on how much the OBD facility is used, you may want to increase the septic pumping frequency or decrease it to once every five years if it receives very little use.
  • Trees, shrubs and woody perennials should be cleared away from system components. Sandfilter surfaces should be mowed at least once per year. If a wet spot appears on or near the sandfilter bed notify the DEP inspector.
  • Mechanical systems operate best if they are used at a consistent rate and may malfunction or produce poor quality effluent if overloaded on the weekend and “starved” during the week. Try to manage laundry, cleaning, and showers so that the load is spread out as evenly as possible. Leave a mechanical OBD operating as recommended by your service contractor at all times during the season of use.
  • Check the chlorine level at least every two weeks and keep fresh chlorine in contact with the treated wastewater. Don’t overfill the chlorinator tubes; only the bottom two or three inches of the tubes should have chlorine. Old, brown or mushy chlorine does not properly disinfect and must be replaced. Take care to remove old chlorine from your chlorinator rather than washing it out to the waterbody.
  • Ensure that the outfall pipe extends to below the low water mark of the receiving waterbody. In extenuating circumstances a specific waiver to this requirement may be granted by the Department.
  • Treated wastewater should be clear and without a strong septic or chlorine odor. If wastewater in the disinfection unit is not nearly clear, smells like rotten eggs, raw sewage, or smells strongly of chlorine, call your service contractor or notify the DEP inspector.

Today we have OBD maintenance and services scheduled in Westport Island, Bowdoinham, Brunswick, Bremen, Orr’s Island, Friendship and Owls Head Maine. If you have an OBD and require a service or you have a question or concern about your OBD please do contact our office on 877-378-4279 or visit www.septicpreservation.com

OBD Services In Maine And Tips For Property Owners To Maintain Their OBDs

Septic Preservation Services have many years experience working with the Maine government’s overboard discharge (OBD) program. As stated on the Maine Gov website:

“The Maine DEP’s Overboard Discharge (OBD) Program is responsible for regulating discharges of sanitary and household wastewater generated at residential or commercial locations to streams, rivers, bays, and the ocean. All OBDs must be approved by the DEP through a licensing process.” For more information see:

http://www.maine.gov/dep/water/wd/OBD/index.html

Septic Preservation Services are the only statewide company on the certified maintenance contractor list provided by the Maine Department of Environmental Protection.

In addition to having your OBD serviced and maintained by a certified contractor you can ensure that your OBD is maintained by following these tips that will help to extend the life of your OBD and promote high quality effluent.

  • Some household chemicals kill the microorganisms that digest the wastes in your treatment system and may pass through to the receiving waterbody.  Toxic chemicals, harsh cleaners, paint, pharmaceuticals, and non-biodegradable materials should not be disposed of by dumping or pouring down the drain.
  • Using low-flow toilets and water-saving showerheads will prolong the life of your system.
  • Septic tanks should be pumped at least once every three years.  Depending on how much the OBD facility is used, you may want to increase the septic pumping frequency or decrease it to once every five years if it receives very little use.
  • Trees, shrubs and woody perennials should be cleared away from system components.  Sandfilter surfaces should be mowed at least once per year.  If a wet spot appears on or near the sandfilter bed notify the DEP inspector.
  • Mechanical systems operate best if they are used at a consistent rate and may malfunction or produce poor quality effluent if overloaded on the weekend and “starved” during the week.  Try to manage laundry, cleaning, and showers so that the load is spread out as evenly as possible.  Leave a mechanical OBD operating as recommended by your service contractor at all times during the season of use.
  • Check the chlorine level at least every two weeks and keep fresh chlorine in contact with the treated wastewater.  Don’t overfill the chlorinator tubes; only the bottom two or three inches of the tubes should have chlorine.  Old, brown or mushy chlorine does not properly disinfect and must be replaced.  Take care to remove old chlorine from your chlorinator rather than washing it out to the waterbody.
  • Ensure that the outfall pipe extends to below the low water mark of the receiving waterbody.  In extenuating circumstances a specific waiver to this requirement may be granted by the Department.
  • Treated wastewater should be clear and without a strong septic or chlorine odor.  If wastewater in the disinfection unit is not nearly clear, smells like rotten eggs, raw sewage, or smells strongly of chlorine, call your service contractor or notify the DEP inspector.

Today we have OBD maintenance and services scheduled in Portland, Falmouth, Orr’s Island, Cape Elizabeth, Freeport and Harpswell Maine. If you have an OBD and require a service or you have question or concern about your OBD please do contact our office on 877-378-4279 or visit https://www.septicpreservation.com

Events

Nothing Found

Sorry, no posts matched your criteria